Mercurial > emacs
diff doc/misc/calc.texi @ 107712:6a80fb868018
Change name of default value of calc-settings-file to ~/.emacs.d/calc.el throughout.
author | Jay Belanger <jay.p.belanger@gmail.com> |
---|---|
date | Tue, 30 Mar 2010 22:47:52 -0500 |
parents | 9f1e7ba8288c |
children | b2e098d47dff |
line wrap: on
line diff
--- a/doc/misc/calc.texi Tue Mar 30 22:53:53 2010 -0400 +++ b/doc/misc/calc.texi Tue Mar 30 22:47:52 2010 -0500 @@ -12167,7 +12167,7 @@ their default values, then settings from the file you named are loaded if this file exists, and this file becomes the one that Calc will use in the future for commands like @kbd{m m}. The default settings -file name is @file{~/.calc.el}. You can see the current file name by +file name is @file{~/.emacs.d/calc.el}. You can see the current file name by giving a blank response to the @kbd{m F} prompt. See also the discussion of the @code{calc-settings-file} variable; @pxref{Customizing Calc}. @@ -16006,7 +16006,7 @@ Selections show deep structure (@kbd{j b}; @pxref{Making Selections}). @item Save -Record modes in @file{~/.calc.el} (@kbd{m R}; @pxref{General Mode Commands}). +Record modes in @file{~/.emacs.d/calc.el} (@kbd{m R}; @pxref{General Mode Commands}). @item Local Record modes in Embedded buffer (@kbd{m R}). @@ -28108,7 +28108,7 @@ @cindex Calc init file, user-defined units The @kbd{u p} (@code{calc-permanent-units}) command stores the user-defined units in your Calc init file (the file given by the variable -@code{calc-settings-file}, typically @file{~/.calc.el}), so that the +@code{calc-settings-file}, typically @file{~/.emacs.d/calc.el}), so that the units will still be available in subsequent Emacs sessions. If there was already a set of user-defined units in your Calc init file, it is replaced by the new set. (@xref{General Mode Commands}, for a way to @@ -28509,7 +28509,7 @@ @cindex Calc init file, variables The @kbd{s p} (@code{calc-permanent-variable}) command saves a variable's value permanently in your Calc init file (the file given by -the variable @code{calc-settings-file}, typically @file{~/.calc.el}), so +the variable @code{calc-settings-file}, typically @file{~/.emacs.d/calc.el}), so that its value will still be available in future Emacs sessions. You can re-execute @w{@kbd{s p}} later on to update the saved value, but the only way to remove a saved variable is to edit your calc init file @@ -30862,7 +30862,7 @@ which are also available outside of Embedded mode. (@pxref{General Mode Commands}.) They are @code{Save}, in which mode settings are recorded permanently in your Calc init file (the file given -by the variable @code{calc-settings-file}, typically @file{~/.calc.el}) +by the variable @code{calc-settings-file}, typically @file{~/.emacs.d/calc.el}) rather than by annotating the current document, and no-recording mode (where there is no symbol like @code{Save} or @code{Local} in the mode line), in which mode-changing commands do not leave any @@ -31122,7 +31122,7 @@ binding permanent so that it will remain in effect even in future Emacs sessions. (It does this by adding a suitable bit of Lisp code into your Calc init file; that is, the file given by the variable -@code{calc-settings-file}, typically @file{~/.calc.el}.) For example, +@code{calc-settings-file}, typically @file{~/.emacs.d/calc.el}.) For example, @kbd{Z P s} would register our @code{sincos} command permanently. If you later wish to unregister this command you must edit your Calc init file by hand. (@xref{General Mode Commands}, for a way to tell Calc to @@ -31855,7 +31855,7 @@ A good place to put your @code{defmath} commands is your Calc init file (the file given by @code{calc-settings-file}, typically -@file{~/.calc.el}), which will not be loaded until Calc starts. +@file{~/.emacs.d/calc.el}), which will not be loaded until Calc starts. If a file named @file{.emacs} exists in your home directory, Emacs reads and executes the Lisp forms in this file as it starts up. While it may seem reasonable to put your favorite @code{defmath} commands there, @@ -34956,7 +34956,9 @@ @code{nil}, then Calc will automatically load your settings file (if it exists) the first time Calc is invoked. -The default value for this variable is @code{"~/.calc.el"}. +The default value for this variable is @code{"~/.emacs.d/calc.el"} +unless the file @file{~/.calc.el} exists, in which case the default +value will be @code{"~/.calc.el"}. @end defvar @defvar calc-gnuplot-name