view lispintro/INSTALL @ 66966:477d7ac04b7b

* message.el (message-courtesy-message) (message-mark-insert-begin, message-mark-insert-end) (message-elide-ellipsis, message-cancel-message) (message-add-header, message-change-subject) (message-cross-post-followup-to-header) (message-cross-post-insert-note, message-reduce-to-to-cc) (message-widen-reply, message-delete-not-region) (message-kill-to-signature, message-insert-signature) (message-insert-importance-high, message-insert-importance-low) (message-insert-or-toggle-importance) (message-insert-disposition-notification-to) (message-indent-citation, message-yank-original) (message-cite-original-without-signature, message-cite-original) (message-insert-citation-line, message-position-on-field) (message-fix-before-sending, message-send-mail-partially) (message-send-mail, message-send-mail-with-sendmail) (message-send-mail-with-qmail, message-send-news) (message-check-news-header-syntax, message-generate-headers) (message-insert-courtesy-copy, message-fill-address) (message-fill-header, message-shorten-references) (message-setup-1, message-cancel-news) (message-forward-make-body-plain) (message-forward-make-body-mime) (message-forward-make-body-mml) (message-encode-message-body) (message-forward-make-body-digest-plain) (message-forward-make-body-digest-mime) (message-use-alternative-email-as-from): Insert `hard-newline' instead of ordinary newlines.

Basic Installation for  An Introduction to Programming in Emacs Lisp  version 2
==================

    # To see the table of contents of the emacs-lisp-intro-2.00.tar.gz
    # file, execute the following at your shell prompt:

    tar -tzvf emacs-lisp-intro-2.00.tar.gz

    # To uncompress and untar the file, execute the following:

    tar -xzvf emacs-lisp-intro-2.00.tar.gz

    # The file will untar into a subdirectory called emacs-lisp-intro-2.00
    # That directory will contain the Texinfo source for the book, the
    # Info files and various other files.

    cd emacs-lisp-intro-2.00

    # To create a DVI file that can be printed directly or converted
    # to PostScript or PDF and then printed, execute the following:

    ./configure
    make dvi

    # To create an HTML file, execute the following
    #   (presumably you have already executed the `./configure' command
    #    before running `make dvi'; if not execute `./configure' now);
    # this will place HTML files into a emacs-lisp-intro/ subdirectory:

    makeinfo --html --verbose emacs-lisp-intro.texi

    # To create a single, large HTML file in the current directory,
    # use the --no-split option, like this:

    makeinfo --html --no-split --verbose emacs-lisp-intro.texi

        # At the time of writing, `makeinfo' version 4.0b creates HTML
        # files with %20 in addresses instead of a space.  Some
        # browsers have difficulty following such references.  In
        # GNU Emacs, you can replace the occurrences of %20 with a
        # command such as
        #              (replace-string "%20" " ")

    # To create a single, large Info file in the current directory
    # instead of the usual 16 smaller Info files, and also, to avoid
    # indenting paragraphs, execute:

    makeinfo --no-split --paragraph-indent=0 --verbose emacs-lisp-intro.texi

    # To create a single, large Plain text file in the current
    # directory, execute:

    makeinfo --fill-column=70 --no-split --paragraph-indent=0 \
    --verbose --no-headers --output=emacs-lisp-intro.txt emacs-lisp-intro.texi

###