comparison Wnn/manual.en/5.op/op3.1 @ 0:bbc77ca4def5

initial import

0:bbc77ca4def5

3.2.3 Operation

(1) Invoking uum

To invoke uum, type "uum" and press the Return key. The lowest line on the
screen is used for as a conversion line.
Data typed in is displayed on this conversion line.

< Figure 2.3.1 >








(2) Input of "readings"

The state where readings are being input is called "reading input mode". 
Text which is converted to kanji is, in principle, always in hiragana.Input 
is always in insert mode. When inputting in the middle of a line, the character 
string to the right of the cursor (including the character under the cursor) 
is pushed sequentially to the right. Readings are displayed underlined.  When a 
"$" is displayed at the head or tail of the conversion line, a portion of the 
line has been scrolled off screen at the head or tail of the line.
 

  Reading Input Mode Functions Table

  Keysym     (Command)| Function
  --------------------+------------------------------------------------
  Right	           ^F | Move the cursor to the right
  Left             ^B | Move the cursor to the left
  F11              ^D |	Delete the character under the cursor
  Meta + Right     ^E |	Move the cursor to the right end of the line
  Meta + Left      ^A |	Move the cursor to the left end of the line
  Meta + Up        ^K |	Delete from the cursor on
  Meta + F13       ^] |	Input description code
		      |	  nn.mm   [Return] 
                      |   (Where nn and mm are the description code for
                      |    the character)
  Meta + F14   ^_  ^? |	Input JIS character codes
	 	      |	  x[x[x[x [Return]   (xxxx: JIS code)
	           ^V |	Directly input the next character typed without
                      | entering it into the conversion process
  --------------------+------------------------------------------------



(3) Conversion

When the convert key is pressed, continuous phrase kana-kanji conversion takes
place, and the "reading" display is replaced with "kana-kanji mixed text", and
edit mode is entered. It is possible to edit in this mode. This is covered in
part (4) following.
If the desired kanji are displayed, then no edit is necessary and you can
proceed directly to the confirmation phase covered in part (5) following.


(4) Editing

When the desired kanji were not displayed by the conversion operation, the text
can be edited by the operations described in the following table. This state is
called "edit mode".

  Edit Mode Function Table

  Keysym     (Command)| Function
  --------------------+---------------------------------------------------------
  Right            ^F | Move the cursor to the right
  Left             ^B | Move the cursor to the left
  Down             ^N | Display the next candidate
  Up               ^P | Display the previous candidate
  F14              ^O | Increase the size of the phrase by one character
  F13              ^I | Decrease the size of the phrase by one character
  Meta + Up        ^K | Return Kanji to the original "reading" they were
                      | converted from.
                      | (From the highlighted phrase on)
  Meta + Right     ^E | Move the phrase indication to the right end of the line
  Meta + Left      ^A | Move the phrase indication to the left end of the line
  Kanji            ^W | Display all candidates (large phrase)
                      |  (All candidates are displayed one line at a time
                      |   numbered (0, 1, 2, ...). If the desired kanji is
                      |   displayed it can be selected by inputting its number.)
                      | Down    Display the next candidate group
                      | Up      Display the previous candidate group
                      | n       Select the candidate (n= 0,1,2,Ž¥Ž¥Ž¥)
                      | ^G      Cancel all candidate display
                   ^Z | Display all candidates (small phrase)
                      |  (All candidates are displayed one line at a time
                      |   numbered (0, 1, 2, ...). If the desired kanji is
                      |   displayed it can be selected by inputting its number.)
                      | Down    Display the next candidate group
                      | Up      Display the previous candidate group
                      | n       Select the candidate (n= 0,1,2,Ž¥Ž¥Ž¥)
                      | ^G      Cancel all candidate display
                   ^C | Return to input mode after conversion
                   ^V | Inspect (Display detailed information about candidates)
  --------------------+---------------------------------------------------------