view ppc/fft_altivec.c @ 7354:456957d86106 libavcodec

My commit at r14340 was not the right solution. For a monochromatic frame, there will be only one centroid and it will be impossible to find three distinct ones. It is better to just avoid shifting if there are not three different centroids.

/*
 * FFT/IFFT transforms
 * AltiVec-enabled
 * Copyright (c) 2003 Romain Dolbeau <[e-mail]>
 * Based on code Copyright (c) 2002 Fabrice Bellard.
 *
 * This file is part of FFmpeg.
 *
 * FFmpeg is free software; you can redistribute it and/or
 * modify it under the terms of the GNU Lesser General Public
 * License as published by the Free Software Foundation; either
 * version 2.1 of the License, or (at your option) any later version.
 *
 * FFmpeg is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public
 * License along with FFmpeg; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
 */
#include "libavcodec/dsputil.h"

#include "gcc_fixes.h"

#include "dsputil_ppc.h"
#include "util_altivec.h"
/*
  those three macros are from libavcodec/fft.c
  and are required for the reference C code
*/
/* butter fly op */
#define BF(pre, pim, qre, qim, pre1, pim1, qre1, qim1) \
{\
    FFTSample ax, ay, bx, by;\
    bx=pre1;\
    by=pim1;\
    ax=qre1;\
    ay=qim1;\
    pre = (bx + ax);\
    pim = (by + ay);\
    qre = (bx - ax);\
    qim = (by - ay);\
}
#define MUL16(a,b) ((a) * (b))
#define CMUL(pre, pim, are, aim, bre, bim) \
{\
    pre = (MUL16(are, bre) - MUL16(aim, bim));\
    pim = (MUL16(are, bim) + MUL16(bre, aim));\
}


/**
 * Do a complex FFT with the parameters defined in ff_fft_init(). The
 * input data must be permuted before with s->revtab table. No
 * 1.0/sqrt(n) normalization is done.
 * AltiVec-enabled
 * This code assumes that the 'z' pointer is 16 bytes-aligned
 * It also assumes all FFTComplex are 8 bytes-aligned pair of float
 * The code is exactly the same as the SSE version, except
 * that successive MUL + ADD/SUB have been merged into
 * fused multiply-add ('vec_madd' in altivec)
 */
void ff_fft_calc_altivec(FFTContext *s, FFTComplex *z)
{
POWERPC_PERF_DECLARE(altivec_fft_num, s->nbits >= 6);
    register const vector float vczero = (const vector float)vec_splat_u32(0.);

    int ln = s->nbits;
    int j, np, np2;
    int nblocks, nloops;
    register FFTComplex *p, *q;
    FFTComplex *cptr, *cptr1;
    int k;

POWERPC_PERF_START_COUNT(altivec_fft_num, s->nbits >= 6);

    np = 1 << ln;

    {
        vector float *r, a, b, a1, c1, c2;

        r = (vector float *)&z[0];

        c1 = vcii(p,p,n,n);

        if (s->inverse) {
            c2 = vcii(p,p,n,p);
        } else {
            c2 = vcii(p,p,p,n);
        }

        j = (np >> 2);
        do {
            a = vec_ld(0, r);
            a1 = vec_ld(sizeof(vector float), r);

            b = vec_perm(a,a,vcprmle(1,0,3,2));
            a = vec_madd(a,c1,b);
            /* do the pass 0 butterfly */

            b = vec_perm(a1,a1,vcprmle(1,0,3,2));
            b = vec_madd(a1,c1,b);
            /* do the pass 0 butterfly */

            /* multiply third by -i */
            b = vec_perm(b,b,vcprmle(2,3,1,0));

            /* do the pass 1 butterfly */
            vec_st(vec_madd(b,c2,a), 0, r);
            vec_st(vec_nmsub(b,c2,a), sizeof(vector float), r);

            r += 2;
        } while (--j != 0);
    }
    /* pass 2 .. ln-1 */

    nblocks = np >> 3;
    nloops = 1 << 2;
    np2 = np >> 1;

    cptr1 = s->exptab1;
    do {
        p = z;
        q = z + nloops;
        j = nblocks;
        do {
            cptr = cptr1;
            k = nloops >> 1;
            do {
                vector float a,b,c,t1;

                a = vec_ld(0, (float*)p);
                b = vec_ld(0, (float*)q);

                /* complex mul */
                c = vec_ld(0, (float*)cptr);
                /*  cre*re cim*re */
                t1 = vec_madd(c, vec_perm(b,b,vcprmle(2,2,0,0)),vczero);
                c = vec_ld(sizeof(vector float), (float*)cptr);
                /*  -cim*im cre*im */
                b = vec_madd(c, vec_perm(b,b,vcprmle(3,3,1,1)),t1);

                /* butterfly */
                vec_st(vec_add(a,b), 0, (float*)p);
                vec_st(vec_sub(a,b), 0, (float*)q);

                p += 2;
                q += 2;
                cptr += 4;
            } while (--k);

            p += nloops;
            q += nloops;
        } while (--j);
        cptr1 += nloops * 2;
        nblocks = nblocks >> 1;
        nloops = nloops << 1;
    } while (nblocks != 0);

POWERPC_PERF_STOP_COUNT(altivec_fft_num, s->nbits >= 6);
}