annotate etc/example.conf @ 13394:455a5056801f

New generic 'portable anymap' video output driver. It supports portable pixmaps and graymaps in both raw and ASCII mode. Besides PPM and PGM, it can also output PGMYUV files which are PGM files with the U and V plane appended to the bottom of the Y image (bottom left and bottom right). All files can be written to the current directory, to a specified output directory or to multiple subdirectories if the filesystem can't handle the amount of files in one directory anymore. Note: This driver is not yet activated and will not be compiled and linked to libvo. A separate patch will take care of that. This is just for adding the file to the repository.

##
## MPlayer configuration file
##
## Configuration files are read system-wide from /usr/local/etc/mplayer.conf
## and per user from ~/.mplayer/config, where per-user settings override
## system-wide settings, all of which are overrriden by the command line.
##
## The options are the same as on the command line.
##


##
## video settings
##

# Specify default video driver (see -vo help for a list).
# vo=xv

# Specify default audio driver (see -ao help for a list).
# ao=oss

# fullscreen mode
# fs=yes

# Change to a different videomode when going fullscreen
# (dga, x11, sdl video output drivers only).
# vm=no

# Force changing display depth (valid settings are: 0, 15, 16, 24, 32).
# May need 'vm=yes' as well, only works with fbdev, dga, svga, vesa
# video output drivers.
# bpp=0

# Enable software scaling (powerful CPU needed).
# Some video output drivers (svga, x11, vesa) do not support hardware scaling.
# zoom=no

# Doublebuffering can help remove flicker from subtitles/OSD.
# double=yes

# standard monitor size, with square pixels
# monitoraspect=4:3

# Use this for a widescreen monitor, non-square pixels.
# monitoraspect=16:9

# Makes the player window stay on top of all other windows.
# ontop=yes

##
## Specify your preferred default skin here
## (skins are searched in /usr/local/share/mplayer/Skin/yourskin
##  and ~/.mplayer/Skin/yourskin)
##
# skin = default

##
## Multiple languages are available :)
##
## Hungarian	igen	nem
## English		yes		no
## German		ja		nein
## Spanish		si		no
## Polish		tak		nie
## Swedish		ja		nej
## Binary		1		0
##
## You can also use spaces and/or tabs.
##

# sound		= 1
# nosound	= nein
# mixer		= /dev/mixer

##
## resample the fonts' alphamap
## 0	plain white fonts
## 0.75	very narrow black outline (default)
## 1	narrow black outline
## 10	bold black outline
##
# ffactor = 0.75

##
## FBdev driver:
##
# framebuffer device to use
# fb = /dev/fb0
#
# mode to use (read from fb.modes)
# fbmode = 640x480-120
#
# location of the fb.modes file
# fbmodeconfig = /etc/fb.modes

## VESA and FBdev driver: Specify your monitor's timings.
##
## (see /etc/X11/XF86Config for timings)
## ** CAUTION! IF YOUR DISPLAY DOESN'T SUPPORT AUTOMATICALLY TURNING OFF WHEN
##    OVERDRIVED (AND EVEN IF IT DOES), THIS MAY CAUSE DAMAGE TO YOUR DISPLAY!
##    WE AREN'T RESPONSIBLE, IT'S YOUR DECISION! **
##
## k, K: means multiply by 1000
## m, M: means multiply by 1.000.000
##
# horizontal frequency range
# monitor-hfreq = 31.5k-50k,70k
#
# vertical frequency range
# monitor-vfreq = 50-90
#
# dotclock (or pixelclock) range
# monitor-dotclock = 30M-300M

##
## SDL driver
##
# Use SDL video with the aalib subdriver by default.
# vo = sdl:aalib
#
# Use SDL audio driver with the esd subdriver by default.
# ao = sdl:esd
#
# Turn off XVideo hardware acceleration.
# noxv = no
#
# Force XVideo even if not detected.
# forcexv = yes


##
## Other (preferred to be default from configfile) switches
##
# Drop frames to preserve audio/video sync.
framedrop 	= yes

##
## cache settings
##
# Use 8MB input cache by default.
cache	        = 8192
#
# Prefill 20% of the cache before starting playback.
cache_min	    = 20.0
#
# Prefill 5% of the cache before restarting playback after the cache emptied.
cache_prefill	= 5.0

# DVD: Display English subtitles if available.
# slang		= en

# DVD: Play English audio tracks if available.
# alang		= en


## This is the correct way to use "subconfig" type options in the
## configuration file. In the command line you use:
## -aop list=resample:fout=44100 , but here it is:
# aop=list=resample:fout=44100

##
## You can also include other configfiles
##
#include = /path/to/the/file/you/want/to/include