Mercurial > mplayer.hg
view DOCS/tech/slave.txt @ 14585:81059277538c
Be less verbose with -v (do not print a line for each demuxed packet)
author | rtognimp |
---|---|
date | Mon, 24 Jan 2005 21:52:24 +0000 |
parents | 74e323b9e5db |
children | a4767edef10d |
line wrap: on
line source
SLAVE MODE PROTOCOL ------------------- FIXME: Some of these options are still not documented, patches welcome. Most slave mode commands are equivalent to command line options. Have a look at the man page for more detailed descriptions. If the -slave option is given, playback is controlled by a line-based protocol. Each line must contain one of the following commands: seek <value> [<type>] Seek to some place in the movie. 0 is a relative seek of +/- <value> seconds (default). 1 is a seek to <value> % in the movie. 2 is a seek to an absolute position of <value> seconds. speed_set <value> Set the speed to <value>. speed_incr <value> Add <value> to the current playback speed. speed_mult <value> Multiply the current speed by <value>. edl_mark Write the current position into the EDL file. audio_delay <value> Adjust the audio delay by <value> seconds. quit [<value>] Quit MPlayer. The optional integer value is used as the return code for the mplayer process (default: 0). pause Pause/unpause the playback. frame_step Play one frame, then pause again. grab_frames Currently unimplemented. pt_step <value> [<force>] Go to the next/previous entry in the playtree. The sign of <value> tells the direction. If no entry is available in the given direction it will do nothing unless force is non-zero. pt_up_step <value> [<force>] Similar to pt_step but jumps to the next/previous entry in the parent list. Useful to break out of the inner loop in the playtree. alt_src_step <value> (ASX playlist only) When more than one source is available it selects the next/previous one. sub_delay <value> [<abs>] Adjust the subtitle delay by +/- <value> seconds or set it to <value> seconds when <abs> is nonzero. sub_step <value> Step forward in the subtitle list by <value> steps or backwards if <value> is negative. osd [<level>] Toggle OSD mode or set it to level when <level> >= 0. osd_show_text <string> Show <string> on the OSD. volume <value> Increase/decrease volume. use_master Switch volume control between master and PCM. mute Mute/unmute sound output. [contrast|gamma|brightness|hue|saturation] <-100 - 100> [<abs>] Set/adjust video parameters. frame_drop [<value>] Toggle/set frame dropping mode. sub_pos <value> Adjust subtitle position. sub_alignment <value> Set subtitle alignment. sub_visibility Toggle subtitle visibility. get_sub_visibility Print out subtitle visibility (1 == on, 0 == off). sub_select Cycle through the available subtitles. Supported subtitle sources are -sub options on the command line, VOBsubs, DVD subtitles, and Ogg text streams. vobsub_lang This is a stub linked to sub_select for backwards compatibility. get_percent_pos Print out the current position in the file, as integer percentage [0-100). get_time_length Print out the length of the current file in seconds. vo_fullscreen Switch to fullscreen mode. get_vo_fullscreen Print out fullscreen status (1 == fullscreened, 0 == windowed). vo_ontop Toggle stay-on-top. vo_rootwin Toggle playback on the root window. switch_vsync [<value>] Toggle vsync (1 == on, 0 == off). If no value is provided, vsync status is inverted. switch_ratio [<value>] Change aspect ratio at runtime. Value is the new aspect ratio expressed as a float (e.g. 1.77778 for 16/9). There might be problems with some video filters. panscan <-1.0 - 1.0> | <0.0 - 1.0> <absolute> Increase or decrease the pan-and-scan range by <value>, 1.0 is the maximum. Negative values decrease the pan-and-scan range. If <absolute> is != 0, then the pan-and scan range is interpreted as an absolute range. loadfile <file|url> Load the given file/URL. loadlist <file> Load the given playlist file. change_rectangle <val1> <val2> Change the position of the rectangle filter rectangle. <val1> Must be one of the following: 0 = width 1 = height 2 = x position 3 = y position <val2> If <val1> is 0 or 1: Integer amount to add/subtract from the width/height. Positive values add to width/height and negative values subtract from it. If <val1> is 2 or 3: Relative integer amount by which to move the upper left rectangle corner. Positive values move the rectangle right/down and negative values move the rectangle left/up. dvdnav <button> Press the given dvdnav button. 1 up 2 down 3 left 4 right 5 menu 6 select dvdnav_event <value> Send <value> as DVDNAV event. DVDNAV support in MPlayer is disabled. tv_step_channel <channel> Select next/previous TV channel. tv_step_norm Change TV norm. tv_step_chanlist Change channel list. tv_set_channel <channel> Set the current TV channel. tv_last_channel Set the current TV channel to the last one. tv_set_freq <frequency in MHz> Set the TV tuner frequency. tv_set_norm <norm> Set the TV tuner norm (PAL, SECAM, NTSC, ...). tv_set_brightness <-100 - 100> Set TV tuner brightness. tv_set_contrast <-100 -100> Set TV tuner contrast. tv_set_hue <-100 - 100> Set TV tuner hue. tv_set_saturation <-100 - 100> Set TV tuner saturation. gui_[loadfile|loadsubtitle|about|play|stop|gui_playlist|gui_preferences|skinbrowser] GUI actions forced_subs_only Display forced subtitles only. dvb_set_channel <channel_number> <card_number> Set DVB channel. screenshot Take a screenshot. Currently not implemented in any video output driver. menu <command> Execute an OSD menu command. up Move cursor up. down Move cursor down. ok Accept selection. cancel Cancel selection. hide Hide the OSD menu. set_menu <menu_name> Display the menu named <menu_name>. help ??? exit ??? hide ??? run <value> Run <value> as shell command. All commands can be prefixed with "pausing ", causing MPlayer to get into paused mode as soon as possible after processing the command. Please note that this can be before the command is fully executed.