view DOCS/Polish/mplayer.1 @ 5834:ece3a19677b9

Fix keypad volume control.

.\" MPlayer (C) 2000-2001 Arpad Gereoffy <[e-mail]-users>
.\" This manpage was/is done by Gabucino
.\"
.TH MPlayer
.SH NAME
mplayer \- Movie Player for Linux
.SH SYNOPSIS
.B mplayer
.RB [ \-gui ]
.RB [ \-v ]
.RB [ \-help / -h / --help ]
.RB [ \-quiet ]
.RB [ \-vo\ <driver>[:<device>] ]
.RB [ \-ao\ <driver>[:<device>] ]
.RB [ \-vcd\ <track\ number> ]
.RB [ \-sb\ <byte\ position> ]
.RB [ \-nosound ]
.RB [ \-abs\ <bytes> ]
.RB [ \-delay\ <secs> ]
.RB [ \-nobps ]
.RB [ \-aid\ <id> ]
.RB [ \-alang\ <audio\ stream\ languages> ]
.RB [ \-vid\ <id> ]
.RB [ \-fps\ <rate> ]
.RB [ \-mc\ <seconds/5f> ]
.RB [ \-fs ]
.RB [ \-vm ]
.RB [ \-zoom ]
.RB [ \-x\ <x> ]
.RB [ \-y\ <y> ]
.RB [ \-sws\ <software\ scaler\ type> ]
.RB [ \-xy\ <factor> ]
.RB [ \-pp\ <quality> ]
.RB [ \-include\ <config\ file> ]
.RB [ \-lircconf\ <config\ file> ]
.RB [ \-ffactor\ <number> ]
.RB [ \-sub\ <filename> ]
.RB [ \-subfps\ <rate> ]
.RB [ \-subdelay\ <seconds> ]
.RB [ \-z\ <0-8> ]
.RB [ \-idx ]
.RB [ \-forceidx ]
.RB [ \-nodshow ]
.RB [ \-noxv ]
.RB [ \-forcexv ]
.RB [ \-ss\ <time> ]
.RB [ \-dumpaudio ]
.RB [ \-dumpvideo ]
.RB [ \-dumpstream ]
.RB [ \-noframedrop ]
.RB [ \-framedrop ]
.RB [ \-nodouble ]
.RB [ \-double ]
.RB [ \-stereo\ <mode> ]
.RB [ \-channels\ <n> ]
.RB [ \-srate\ <Hz> ]
.RB [ \-osdlevel\ <level> ]
.RB [ \-config\ <file> ]
.RB [ \-display\ <name> ]
.RB [ \-wid\ <window\ id> ]
.RB [ \-unicode ]
.RB [ \-utf8 ]
.RB [ \-fsmode\ <mode> ]
.RB [ \-vc\ <video\ codec\ name> ]
.RB [ \-ac\ <audio\ codec\ name> ]
.RB [ \-vfm\ <video\ codec\ family> ]
.RB [ \-afm\ <audio\ codec\ family> ]
.RB [ \-frames\ <number> ]
.RB [ \-autoq\ <quality> ]
.RB [ \-fb\ <device> ]
.RB [ \-fbmode\ <modename> ]
.RB [ \-fbmodeconfig\ <filename> ]
.RB [ \-monitor_hfreq\ <horizontal\ frequency\ range> ]
.RB [ \-monitor_vfreq\ <vertical\ frequency\ range> ]
.RB [ \-monitor_dotclock\ <dotclock\ (or\ pixelclock)\ range> ]
.RB [ \-benchmark ]
.RB [ \-dvd\ <title\ id> ]
.RB [ \-chapter\ <chapter\ id> ]
.RB [ \-dvdangle\ <angle\ id> ]
.RB [ \-alang\ <country\ code> ]
.RB [ \-slang\ <country\ code> ]
.RB [ \-sid\ <subtitle \id> ]
.RB [ \-dvdkey\ <key> ]
.RB [ \-skin\ <skin\ name> ]
.RB [ \-aspect\ <ratio> ]
.RB [ \-monitoraspect\ <ratio> ]
.RB [ \-subcp\ <codepage> ]
.RB [ \-dumpmpsub ]
.RB [ \-dumpfile ]
.RB [ \-dumpsub ]
.RB [ \-screenw\ <pixels> ]
.RB [ \-screenh\ <pixels> ]
.RB [ \-cache\ <kbytes> ]
.RB [ \-bpp\ <depth> ]
.RB [ \-flip ]
.RB [ \-playlist\ <filename> ]
.RB [ \-slave ]
.RB [ \-loop\ <num> ]
.RB [ \-mixer\ <device> ]
.RB [ \-master\ yes/no ]
.RB [ \-tv\ suboptions ]
.RB [ \-dapsync ]
.RB [ \-softsleep ]
.I < - | file | URL | device >
.PP
.SH DESCRIPTION
.I mplayer
MPlayer is a movie player for LINUX (runs on many other Unices, and non-x86
CPUs, see section 6). It plays most MPEG, AVI and ASF/WMV files, supported by
many native and Win32 DLL codecs. You can watch VideoCD, SVCD, DVD, and even
DivX movies too (and you don't need the avifile library at all!).

Another big feature of mplayer is the wide range of supported output drivers :
X11, Xv, DGA, OpenGL, SVGAlib, fbdev, AAlib, DirectFB, SDL (and all the drivers
it supports), and some lowlevel card-specific drivers (for Matrox, 3Dfx and
Radeon) too! Most of them supports software or hardware scaling, so you can
enjoy movies in fullscreen.

Several subtitles types are supported (curently 9 !) and the fonts are
rendered with nice big antialiased shaded fonts ! Of course there is support
for european/ISO 8859-1,2 (hungarian, english, czech, etc), cyrillic, korean
fonts.
.LP
.SH "GUI OPTIONS"
.I NOTE:
The GUI code has to be compiled in *explicitly*, for details see the
documentation.
.TP
.B \-gui
start MPlayer in GUI mode.
.TP
.B \-skin <skin\ directory>
load skin from this directory (WITHOUT path name!). For example '-skin fittyfene' tries these :

    /usr/local/share/mplayer/Skin/fittyfene
    ~/.mplayer/Skin/fittyfene
.LP
.SH "DVD OPTIONS"
.I NOTE:
These options are valid only with DVD support compiled in. For details,
see the documentation.
.TP
.B \-dvd\ titleid
tell MPlayer which movies (marked with titleid) to play. For example
sometimes '1' are trailers, and '2' is the real movie.
.TP
.B \-sid\ <id>
Turns on DVD subtitle displaying. Also, you MUST specify a number which
corresponds to a DVD subtitle language (0-31). For the list of available
subtitles, use with the -v switch and look at the output.
.TP
.B \-chapter\ <chapter\ id>
specify which chapter to start playing at. Examples can be found below.
.TP
.B \-dvdangle\ <angle\ id>
some DVD discs contain scenes that can be viewed from multiple angles.
Here you can tell MPlayer which angles to use. Examples can be found below.
.TP
.B \-alang\ <audio\ stream\ language>
Used when playing DVD disks. Expects a two-letter country code(s) as
parameter, and always tries to play back audio streams those language
matches the given code. For example: -alang hu,en will always try to play
hungarian or if it's non-existant then english audio streams if there are any.
.TP
.B \-slang\ <subtitle\ language>
See the former, but this option needs a two-letter parameter, a country code.
Like: -slang hu,en will always select hungarian or if it's non existant then
english subtitles, if there are any. For the list of available subtitles, use
with the -v switch and look at the output.
.LP
.SH "GENERAL OPTIONS"
.TP
.I NOTE
Every "flag" option has "noflag" pair, e.g. -fs opposite is -nofs
.TP
.B \-vo\ <driver>[:<device>]
select video output driver and optinaly device. "device" is valid with
SDL and GGI too, it means sub-driver then (for example: -vo sdl:aalib).

you can get the list of available drivers executing
.I mplayer -vo help

.TP
.B \-ao\ <driver>[:<device>]
select audio output driver and optinaly device. "device" is valid with
SDL too, it means sub-driver then (for example: -vo sdl:esd).

If using OSS, you can specify which sound device to use like this :
-ao oss:/dev/dsp1     (replaces the old -dsp option)

you can get the list of available drivers executing
.I mplayer -ao help

.TP
.B \-vcd\ <track>
play video cd track from device instead of plain file
.TP
.B \-nosound
don't play sound
.TP
.B \-fs
fullscreen playing (centers movie, and makes black
bands around it)
.TP
.B \-vm
try to change to a different video mode. dga2, x11 (XF86VidMode) and sdl
output drivers support it.
.TP
.B \-zoom
use software scaling, where available (use with -nofs). svga, x11, vesa
output drivers support it.
.TP
.B \-flip
flip image (useful for example for old Indeo codecs). Supported only(?)
by the 'sdl' and 'x11' outputs.
.TP
.B \-x\ <x>
scale image to x width (if driver suppports)
.TP
.B \-y\ <y>
scale image to y height (if driver supports)
.TP
.B \-sws\ <software\ scaler\ type>
this option sets the quality (and speed, respectively) of the software scaler,
with the -zoom option. For example with x11 or other outputs which lack
hardware acceleration. Possible settings are :

    0 - fast bilinear (default)
    1 - bilinear
    2 - bicubic (best quality)
.TP
.B \-xy\ <factor>
scale image by <factor>
.TP
.B \-autoq\ <quality>
dynamically changes the level of postprocess, depending on spare CPU
time available. Uses the same value ranges as -pp . The number you
specify will be the maximum level used. Usually you can use some big
number. You don't have to (and don't) use together with -pp !
.TP
.B \-ffactor\ <number>
resample alphamap of the font. Can be:

        0    plain white fonts
        0.75 very narrow black outline [default]
        1    narrow black outline
        10   bold black outline
.TP
.B \-sub\ <subtitle\ file>
use/display this subtitle file
.TP
.B \-subfps\ <rate>
specify frame/sec rate of subtitle file (float number)
(ONLY for frame-based SUB files, i.e. NOT MicroDVD format!)
(default: the same fps as the movie)
.TP
.B \-subdelay\ <sec>
delays subtitles by <sec> seconds. Can be negative.
.TP
.B \-osdlevel\ <level>
specifies which mode the OSD should start in (0 : none, 1 : seek, 2: seek+timer)
(default = 2)
.TP
.B \-lircconf\ <config\ file>
specifies a configfile for LIRC (see http://www.lirc.org) if you don't like the default ~/.lircrc
.TP
.B \-v
enable verbose output (more -v means more verbosity)
.TP
.B \-quiet
display less output, status messages.
.TP
.B \-benchmark
used in combination with -nosound and -vo null for benchmarking.
.TP
.B \-aspect <ratio>
set aspect ratio of movies. It's autodetected on MPEG files, and can't be
autodetected on AVI files. Examples:

    -aspect 4:3  or -aspect 1.3333
    -aspect 16:9 or -aspect 1.7777

.TP
.B \-monitoraspect <ratio>
set aspect ratio of your screen. Examples:

    -monitoraspect 4:3  or 1.3333
    -monitoraspect 16:9 or 1.7777

.TP
.B \-playlist <file>
play files according to this filelist (1 file/row).
.TP
.B \-ss\ <time>
seek to given time position. For example :

    -ss 56         seeks to 56 seconds
    -ss 01:10:00   seeks to 1 hour 10 min

.TP
.B \-loop\ <num>
loops movie playback <num> times. 0 means forever.
.TP
.B \-mixer\ <device>
this option will tell MPlayer to use a different device for mixing than
/dev/mixer.
.TP
.B \-master\ yes/no
Setting this option to "yes" will instruct MPlayer to change the MASTER
mixer channel when setting the volume, and "no" means the PCM channel.
.TP
.B \-tv\ suboptions
this option enables the TV grabbing feature of MPlayer. For complete
documentation, please see documentation.html chapter 2.5
.IP
.SH "ADVANCED OPTIONS"
.TP
.I NOTE
These options can help you solve your particular problem.. Also, see the
documentation !
.TP
.B \-vc <name>
force usage of a specific video codec, according to its name in codecs.conf,
for example :

    -vc divx       use VFW DivX codec
    -vc divxds     use DirectShow DivX codec
    -vc ffdivx     use libavcodec's DivX codec
    -vc ffmpeg12   use libavcodec's MPEG1/2 codec
    -vc divx4      use ProjectMayo's DivX codec

See '-vc help' for FULL list !
.TP
.B \-ac <name>
force usage of a specific audio codec, according to its name in codecs.conf,
for example :

    -ac mp3        use libmp3 MP3 codec
    -ac mp3acm     use l3codeca.acm MP3 codec
    -ac ac3        use AC3 codec
    -ac hwac3      enable Hardware AC3 passthrough
                   (see documentation)
    -ac vorbis     use libvorbis
    -ac ffmp3      use ffmpeg's MP3 decoder (SLOW)

See '-ac help' for FULL list !
.TP
.B \-vfm <1-12>
force usage of a specific codec FAMILY, and FALLBACK to default if failed.
For example:

    -vfm 2         use VFW (Win32) codecs
    -vfm 3         use OpenDivX/DivX4 codec (YV12)
                   (same as -vc odivx but fallback)
    -vfm 4         use DirectShow (Win32) codecs
    -vfm 5         use libavcodec codecs
    -vfm 7         use DivX4 codec (YUY2)
                   (same as -vc divx4 but fallback)
    -vfm 10        use XAnim codecs

See -vc help for FULL list !

.I NOTE:
if libdivxdecore support was compiled in, then type 3 and 7 now contains
just the same DivX4 codec, but different APIs to reach it. For difference
between them and when to use which, check the DivX4 section in the
documentation.
.TP
.B \-afm <1-12>
force usage of a specific audio format. For example:

    -afm 1         use libmp3 (mp2/mp3, but not mp1)
    -afm 2         suppose raw PCM audio
    -afm 3         use libac3
    -afm 4         use a matching Win32 codec
    -afm 5         use aLaw/uLaw driver
    -afm 10        use libvorbis
    -afm 11        use ffmpeg's MP3 decoder (even mp1)

See -ac help for FULL list !
.TP
.B \-sb\ <byte\ position>
seek to byte position
.TP
.B \-bpp\ <depth>
use different color depth than autodetect. Not all -vo drivers support
it (fbdev, dga2, svga, vesa).
.TP
.B \-pp\ <quality>
apply postprocess filter on decoded image.
Postprocessing effect depends on the codec and works only for MPEG, OpenDivX,
DivX4, DivX. Quality is an hexadecimal number built as below:

0x 00 TX hv YZ
      ^^ ^^ ^^
      ||  | ||
      ||  | |\- postprocessing flag for luminance:
      ||  | |   1/2: v/h deblock  4: dering
      ||  | |   8: auto contrast/brightness correction
      ||  | |
      ||  | \-- postproc flags for color:
      ||  |     1/2: v/h deblock  4: dering
      ||  |
      ||  \---- experimental deblocking filters:
      ||        11: X's filter 22: x1 filter
      ||
      |\------- deinterlacing modes
      |         1: linear interpolation  2: linear blend
      |         4: cubic interpolation   8: median
      |
      \-------- temporal denoise filter: 1 enabled
	
.I HINT:
0x2007f or 0x7f are known to give good results.
.I NOTE:
0x20000 (deinterlacing) may be required for DVD playback 
.TP
.B \-npp\ <options> (EXPERIMENTAL)
This option allows to give more litterate options for postprocessing, and is
another way of calling it (not with -pp).

.I EXAMPLE:
    '-pp 0x2007f' <=> '-npp hb,vb,dr,al,lb'
    '-pp 0x7f'    <=> '-npp hb,vb,dr,al'

The options for -npp are a coma separated list of the keywords below:
    de or default        : hdeblock:a,vdeblock:a,
                           dering:a,autolevels,tmpnoise:a:150:200:400 (0xTODO)
    fa or fast           : x1hdeblock:a,x1vdeblock:a,
                           dering:a,autolevels,tmpnoise:a:150:200:400 (0xTODO)
    hb or hdeblock       : horizontal deblocking filter (0xTODO)
    vb or vdeblock       : vertical deblocking filter (0xTODO)
    hr or rkhdeblock     : rk horizontal deblock filter (0xTODO)
    vr or rkvdeblock     : rk vertical deblock filter (0xTODO)
    h1 or x1hdeblock     : x1 horizontal deblock filter (0xTODO)
    v1 or x1vdeblock     : y1 horizontal deblock filter (0xTODO)
    dr or dering         : TODO
    al or autolevels     : brightness/contrast correction (0xTODO)
    lb or linblenddeint  : linear blend deinterlacing (0x20000)
    li or linipoldeint   : linear interpolation deinterlacing (0x10000)
    ci or cubicipoldeint : cubic interpolation deinterlacing (0x40000)
    md or mediandeint    : median deinterlacing (0x80000)
    tn or tmpnoise       : temporal denoise filter (0x100000)

These keywords accept a '-' prefix to disable the option.

.I EXAMPLE:
    '-npp de,-al' means 'default filters without brightness/contrast correction'

A postfix letter, separated by ':' may be appended to the option to indicate
its scope:
    a : automatically switches the filter off if the cpu is too slow
    c : do chrominance filtering too
    y : do not do chrominance filtering (that is only luminance filtering)

Each filter defaults to 'c' (chrominance).

.I EXAMPLE:
    '-npp de,tn:1:2:3' means 'enable default filters & temporal denoiser'
    '-npp hb:y,vb:a -autoq 6' means 'deblock horizontal only luminance, and
    automatically switch vertical deblocking on/off depending on available 
    cpu time'

.I HINT:
    the following values are known to give good results:
    -npp default -autoq 6 and -npp tn:150:200:400 for the denoiser

.TP
.B \-slave
This option switches on slave mode. This is intended for use
of MPlayer as a backend to other programs. Instead of intercepting keyboard
events, MPlayer will read simplistic command lines from its stdin.
See section
.B SLAVE MODE PROTOCOL
for the syntax.
.TP
.B \-abs\ <bytes>
sound card audio buffer size (in bytes, default: measuring)
.TP
.B \-delay\ <secs>
audio delay in seconds (may be +/- float value)
.TP
.B \-nobps
don't use avg. byte/sec value for A-V sync (AVI)
.TP
.B \-aid\ <id>
select audio channel [MPG: 0-31 AVI: 1-99 ASF: 0-127 VOB: 128-...]
.TP
.B \-vid\ <id>
select video channel [MPG: 0-15  AVI:  -- ]
.TP
.B \-fps\ <value>
force frame rate (if value is wrong in the header) (float number)
.TP
.B \-mc\ <seconds/5frame>
maximum sync correction per 5 frames (in seconds)
.TP
.B \-ni
force usage of non-interleaved AVI parser (fixes playing
of some bad AVI files)
.TP
.B \-include configfile
specify config file to be parsed after the default
.TP
.B \-z\ <0-8>
specifies compression level for PNG output
          0 : no compression
          8 : max compression
.TP
.B \-idx
rebuilds INDEX of the AVI. Useful with broken downloads, or badly
created AVIs.
.TP
.B \-forceidx
force rebuilding of INDEX. Useful for testing, or AVIs with bad
indexes.
.TP
.B \-nodshow
disables usage of DirectShow video codecs
.TP
.B \-noxv (SDL only)
disable XVideo hardware acceleration
.TP
.B \-forcexv (SDL only)
force using XVideo
.TP
.B \-dumpaudio
writes audio stream of the file to ./stream.dump (mostly usable
with mpeg/ac3)
.TP
.B \-dumpstream
dumps the file to ./stream.dump . Useful for example
when ripping from DVD.
.TP
.B \-noframedrop
no frame dropping : every frame is played, audio and video may be out of
sync (default)
.TP
.B \-framedrop
frame dropping : decode all frames, video may skip
.TP
.B \-nodouble
disables doublebuffering.
With the DGA driver this also disables OSD support but yields some speed gain.
.TP
.B \-dvdkey key
key to decrypt stream encrypted with CSS. For example : -dvdkey F169072699
(this is NOT for DVD playing! For DVD use the -dvd option!)
.TP
.B \-stereo mode
select type of MP2/MP3 stereo output.

        Stereo         0
        Left channel   1
        Right channel  2
.TP
.B \-channels n
select number of audio output channels to be used

        Stereo         2
        Surround       4
        Full 5.1       6

Currently this option is only honoured for AC3 audio.
.TP
.B \-srate <Hz>
specifies Hz to playback audio on. Has effect on playback speed!
.TP
.B \-config <config\ file>
specifies where to search for config file
.TP
.B \-display <name>
specify the hostname and display number of the X server you want
to display on. For example : -display xtest.localdomain:0
.TP
.B \-wid\ <window\ id>
This tells MPlayer to use a X11 window, which is useful to embed MPlayer in a
browser (with the plugger extension for instance)
.IP
.B \-unicode
tells MPlayer to handle the subtitle file as UNICODE.
Contrary: -nounicode
.TP
.B \-utf8
tells MPlayer to handle the subtitle file as UTF8.
.TP
.B \-fsmode\ mode
This option workarounds some problems when using specific windowmanagers and
fullscreen mode. If you experience fullscreen problems, try changing this
value between 0 and 7.

        -fsmode 0      new method
        -fsmode 1      ICCCWM patch
                       (for KDE2/icewm)
        -fsmode 2      old method
        -fsmode 3      ICCCWM patch
                       plus Motif method
.TP
.B \-frames\ number
MPlayer plays <number> frames, then quits.
.TP
.B \-fb\ <device> (FBdev or DirectFB only)
Specifies the framebuffer device to use. By default it uses /dev/fb0 .
.TP
.B \-fbmode\ <modename> (FBdev only)
Change videomode to the one that is labelled as <modename> in /etc/fb.modes .
.TP
.I NOTE
VESA framebuffer doesn't support mode changing.
.TP
.B \-fbmodeconfig\ <filename> (FBdev only)
Use this config file instead of the default /etc/fb.modes .
Only valid for the fbdev driver.
.TP
.B \-monitor_hfreq <horizontal frequency range>  (FBdev only)
.TP
.B \-monitor_vfreq <vertical frequency range>  (FBdev only)
.TP
.B \-monitor_dotclock <dotclock\ (or\ pixelclock) range>  (FBdev only)
Look into etc/example.conf for further information and in DOC/video.html.
.TP
.B \-subcp\ codepage
If your system supports iconv(3), you can use this option to
specify codepage of the subtitle. Examples:

        -subcp latin2
        -subcp cp1250

.TP
.B \-dumpmpsub
Convert the given subtitle (specified with the -sub switch) to MPlayer's
subtitle format, MPsub. Dumps a dump.mpsub file to current directory.
.TP
.B \-screenw\ <pixels>
If you use an output driver which can't know the resolution of the screen
(mga/fbdev/x11 and/or TVout) this is where you can specify the horizontal
resolution.
.TP
.B \-screenh\ <pixels>
If you use an output driver which can't know the resolution of the screen
(mga/fbdev/x11 and/or TVout) this is where you can specify the vertical
resolution.
.TP
.B \-cache\ <kbytes>
This option specifies how much memory to use when precaching a file/URL.
Especially useful on slow media. Default is off.
.IP
.SH "ALPHA/BETA CODE"
.TP
.I NOTE
These are included in this manpage just for completeness! These may or may NOT
work! If you don't know what are these, you DON'T need these! In either case,
double-check the documentation !
.TP
.B \-dumpvideo
dump video stream to ./stream.dump (only with MPEG-PS) (not very usable)
.IP
.SH KEYBOARD CONTROL
.TP
.I NOTE
These keys may/may not work, depending on your video output driver.
.TP
	  <-  or  ->      seek backward/forward  10 seconds

up or down      seek backward/forward   1 minute

pgup/pgdown     seek backward/forward  10 minutes

p or SPACE      pause movie (press any key)

q or ESC        stop playing and quit program

+ or -          adjust audio delay by +/- 0.1 second

/ or *          decrease/increase volume

o               toggle OSD: none / seek / seek+timer

m               toggle using master/pcm volume

z or x          adjust subtitle delay by +/- 0.1 second

(the following keys are valid only when using DirectShow DivX codec, or
the DivX4 codec with -vc divx4)

1 or 2          adjust contrast

3 or 4          adjust brightness

5 or 6          adjust hue

7 or 8          adjust saturation

.IP
.SH SLAVE MODE PROTOCOL
If the -slave switch is given, playback is controlled by a 
line-based protocol with the following tokens:
.TP
       stop            pause playback

play            resume playback

seek <NUM>      continue at second NUM

skip <NUM>      skip NUM seconds (may be negative)

quit            exit MPlayer

.IP
.SH FILES AND DIRECTORIES
.TP
.I CONFIG FILES
Settings are stored system-wide in the /etc/mplayer.conf file,
and per-user in $HOME/.mplayer/config. The directory
$HOME/.mplayer and the 'config' are created if doesn't exist.
.TP
.I FONTS
Fonts are searched in $HOME/.mplayer/font. There must be a font.desc
file, and files with .RAW extension.
.TP
.I SUBTITLE FILES
MPlayer currently supports 9 subtitle formats : MicroDVD, SubRip, unnamed,
SAMI (smi), vplayer, RealMedia RT, ssa (Sub Station Alpha), AQT, and our own: MPsub.
Sub files are searched in this priority : (for example /mnt/cdrom/movie.avi)
    /mnt/cdrom/movie.sub
     (utf/UTF/sub/SUB/srt/SRT/smi/SMI/rt/RT/txt/TXT/ssa/SSA)
    $HOME/.mplayer/sub/movie.sub
     (utf/UTF/sub/SUB/srt/SRT/smi/SMI/rt/RT/txt/TXT/ssa/SSA)
    $HOME/.mplayer/default.sub
.IP
.SH "EXAMPLES"
.B Quickstart DVD playing
mplayer -dvd 1
.TP
.B Multiangle DVD playing
mplayer -dvd 1 -dvdangle 2
.TP
.B Playing from a different DVD device
mplayer -dvd 1 /dev/dvd2
.TP
.B Stream from HTTP
mplayer http://mplayer.hq/example.avi
.TP
.B Convert subtitle to MPsub (to ./dump.mpsub)
mplayer dummy.avi -sub source.sub -dumpmpsub
.LP
.SH BUGS
Probably. Check the documentation.

Bugreports should be addressed to the MPlayer-users mailing list
([e-mail]) ! If you want to submit a bugreport
(which we love to receive!), please double-check the bugreports.html, and
tell us all that we need to know to identify your problem.

.LP
.SH AUTHORS
Check documentation !

MPlayer is (C) 2000-2001
.I Arpad Gereoffy <[e-mail]-users>

This manpage is written and maintained by
.I Gabucino .
.LP
.SH STANDARD DISCLAIMER
Use only at your own risk! There may be errors and inaccuracies that could
be damaging to your system or your eye. Proceed with caution, and although
this is highly unlikely, the author doesn't take any responsibility for that!
.\" end of file