view doc/xfer-signals.dox @ 20996:ec3736fe2e4e

There's an #ifdef in MSIM which, if enabled, allows the user to specify which information should be show in the status line. By default it shows the buddy's server-side alias, which is contrary to Pidgin's default use of this line, and the code to allow configuration is also off by default. This makes the "Headline" which is effectively your status message display by default instead. Fixes #3064

/** @page xfer-signals File Transfer Signals

 @signals
  @signal file-recv-accept
  @signal file-recv-start
  @signal file-recv-cancel
  @signal file-recv-complete
  @signal file-recv-request
  @signal file-send-accept
  @signal file-send-start
  @signal file-send-cancel
  @signal file-send-complete
 @endsignals

 @see ft.h

 <hr>

 @signaldef file-recv-accept
  @signalproto
void (*file_recv_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-start
  @signalproto
void (*file_recv_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-cancel
  @signalproto
void (*file_recv_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-complete
  @signalproto
void (*file_recv_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-request
  @signalproto
void (*file_recv_request)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted before the user is prompted for an incoming file-transfer.
   Plugins can intercept the signal to auto-accept/auto-reject the
   requests. To auto-accept the file transfer, use
   purple_xfer_request_accepted(). To auto-reject, set the status of the
   xfer to PURPLE_XFER_STATUS_CANCEL_LOCAL.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-accept
  @signalproto
void (*file_send_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-start
  @signalproto
void (*file_send_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-cancel
  @signalproto
void (*file_send_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-complete
  @signalproto
void (*file_send_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 */
// vim: syntax=c.doxygen tw=75 et