view doc/xfer-signals.dox @ 25172:fd5eedf131b4

Generalize the FQY command so it can be used by different callbacks based on the place that called it. Then automatically call an FQY when sending the buddy list ADL's for a buddy with an unknown network. Then we can send a corrected ADL later with the network from the FQY. This should make it easier for people with OCS/Yahoo contacts that were added incorrectly by previous versions, as they shouldn't need to mess with their address book outside of Pidgin (but if there are multiple buddy copies, that may need fixing externally). I should probably figure out how to permanently fix the Membership lists, eventually. References #6755. References #3322

/** @page xfer-signals File Transfer Signals

 @signals
  @signal file-recv-accept
  @signal file-recv-start
  @signal file-recv-cancel
  @signal file-recv-complete
  @signal file-recv-request
  @signal file-send-accept
  @signal file-send-start
  @signal file-send-cancel
  @signal file-send-complete
 @endsignals

 @see ft.h

 <hr>

 @signaldef file-recv-accept
  @signalproto
void (*file_recv_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-start
  @signalproto
void (*file_recv_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-cancel
  @signalproto
void (*file_recv_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-complete
  @signalproto
void (*file_recv_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-request
  @signalproto
void (*file_recv_request)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted before the user is prompted for an incoming file-transfer.
   Plugins can intercept the signal to auto-accept/auto-reject the
   requests. To auto-accept the file transfer, use
   purple_xfer_request_accepted(). To auto-reject, set the status of the
   xfer to PURPLE_XFER_STATUS_CANCEL_LOCAL.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-accept
  @signalproto
void (*file_send_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-start
  @signalproto
void (*file_send_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-cancel
  @signalproto
void (*file_send_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-complete
  @signalproto
void (*file_send_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 */
// vim: syntax=c.doxygen tw=75 et