annotate doc/xfer-signals.dox @ 18756:9b0fd9a4d01b

For XMPP multi-selection lists in generic data forms, the intent here was to use the option value as the label in the event that the label wasn't specified, but the wrong variable was being set. This probably happens only very rarely, because the label is pretty much always set. In fact, it wouldn't suprise me if this has never happened.

/** @page xfer-signals File Transfer Signals

 @signals
  @signal file-recv-accept
  @signal file-recv-start
  @signal file-recv-cancel
  @signal file-recv-complete
  @signal file-recv-request
  @signal file-send-accept
  @signal file-send-start
  @signal file-send-cancel
  @signal file-send-complete
 @endsignals

 <hr>

 @signaldef file-recv-accept
  @signalproto
void (*file_recv_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-start
  @signalproto
void (*file_recv_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-cancel
  @signalproto
void (*file_recv_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-complete
  @signalproto
void (*file_recv_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-request
  @signalproto
void (*file_recv_request)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted before the user is prompted for an incoming file-transfer.
   Plugins can intercept the signal to auto-accept/auto-reject the
   requests. To auto-accept the file transfer, use
   purple_xfer_request_accepted(). To auto-reject, set the status of the
   xfer to PURPLE_XFER_STATUS_CANCEL_LOCAL.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-accept
  @signalproto
void (*file_send_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-start
  @signalproto
void (*file_send_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-cancel
  @signalproto
void (*file_send_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-complete
  @signalproto
void (*file_send_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 */
// vim: syntax=c tw=75 et