view doc/xfer-signals.dox @ 22493:2c757739ee77

Fix a problem with our configure check for sys/sysctl.h on OpenBSD 4.2. It was printing the following message: checking sys/sysctl.h usability... no checking sys/sysctl.h presence... yes configure: WARNING: sys/sysctl.h: present but cannot be compiled configure: WARNING: sys/sysctl.h: check for missing prerequisite headers? configure: WARNING: sys/sysctl.h: see the Autoconf documentation configure: WARNING: sys/sysctl.h: section "Present But Cannot Be Compiled" configure: WARNING: sys/sysctl.h: proceeding with the preprocessor's result configure: WARNING: sys/sysctl.h: in the future, the compiler will take precedence configure: WARNING: ## ------------------------------ ## configure: WARNING: ## Report this to [e-mail] ## configure: WARNING: ## ------------------------------ ## Turns out sys/sysctl.h on OpenBSD 4.2 requires that sys/param.h be included for it to compile. This was reported to our devel mailing list by David Hill on December 11th, 2007. See http://www.gnu.org/software/autoconf/manual/autoconf.html#Generic-Headers for the documentation on AC_CHECK_HEADERS

/** @page xfer-signals File Transfer Signals

 @signals
  @signal file-recv-accept
  @signal file-recv-start
  @signal file-recv-cancel
  @signal file-recv-complete
  @signal file-recv-request
  @signal file-send-accept
  @signal file-send-start
  @signal file-send-cancel
  @signal file-send-complete
 @endsignals

 @see ft.h

 <hr>

 @signaldef file-recv-accept
  @signalproto
void (*file_recv_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-start
  @signalproto
void (*file_recv_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-cancel
  @signalproto
void (*file_recv_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-complete
  @signalproto
void (*file_recv_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an incoming file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-recv-request
  @signalproto
void (*file_recv_request)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted before the user is prompted for an incoming file-transfer.
   Plugins can intercept the signal to auto-accept/auto-reject the
   requests. To auto-accept the file transfer, use
   purple_xfer_request_accepted(). To auto-reject, set the status of the
   xfer to PURPLE_XFER_STATUS_CANCEL_LOCAL.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-accept
  @signalproto
void (*file_send_accept)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been accepted.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-start
  @signalproto
void (*file_send_start)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has started.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-cancel
  @signalproto
void (*file_send_cancel)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been canceled.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 @signaldef file-send-complete
  @signalproto
void (*file_send_complete)(PurpleXfer *xfer, gpointer data);
  @endsignalproto
  @signaldesc
   Emitted when an outgoing file transfer has been completed.
  @param xfer The file transfer
  @param data User data
 @endsignaldef

 */
// vim: syntax=c.doxygen tw=75 et