annotate DOCS/tech/slave.txt @ 10579:f25d93203a71

From: Kir Kostuchenko <[e-mail]> Hi, I found that command line options brightness, hue, contrast and saturation does not works, becouse mplayer apply it, before open tv (kernel says invalid ioctl). Here are simple fix. Please apply.

SLAVE MODE PROTOCOL
-------------------

If the -slave option is given, playback is controlled by a line-based protocol.
Each line must contain one of the following commands:

seek <value> [type=<0/\:1/\:2>]
	Seek to some place in the movie.
	Type 0 is a relative seek of +/\:- <value> seconds.
	Type 1 seek to <value> % in the movie.
	Type 2 is a seek to an absolute position of <value> seconds.
edl_mark
	????
audio_delay <value>
	Adjust the audio delay of value seconds
quit
	Quit MPlayer
pause
	Pause/\:unpause the playback
grap_frames
	Somebody know ?
pt_step <value> [force=<value>]
	Go to next/\:previous entry in the playtree.
pt_up_step <value> [force=<value>]
	Like pt_step but it jumps to next/\:previous in the parent list.
alt_src_step <value>
	When more than one source is available it selects the next/\:previous one
	(only supported by asx playlist).
sub_delay <value> [abs=<value>]
	Adjust the subtitles delay of +/\:- <value> seconds or set it to <value>
	seconds when abs is non zero.
osd [level=<value>]
	Toggle OSD mode or set it to level when level >= 0.
volume <dir>
	Increase/\:decrease volume
use_master
	Switch volume control between master and pcm.
mute
	Mute/\:unmute sound output.
[contrast|brightness|hue|saturation] <-100-100> [abs=<value>]
	Set/\:Adjust video parameters.
frame_drop [type=<value>]
	Toggle/\:Set frame dropping mode.
sub_alignment <value>
	Set subtitle alignment.
sub_visibility
	Toggle subtitle visibility.
sub_pos <value>
	Adjust subtitles position.
vobsub_lang
	Switch the subtitle language when using VOBSub subtitles.
get_percent_pos
	???
get_time_length
	???
vo_fullscreen
	Switch to fullscreen mode.
panscan value [value2]
	???
loadfile url
	Load the given file/\:url.
loadlist file
	Load the given playlist file.
change_rectangle val1 val2
	??? used by the rectangle video filter.
dvdnav button
	Press the given dvdnav button.
	1 is up, 2 is down, 3 is left, 4 is right, 5 is menu and 6 is select.
tv_step_channel <dir>
	Select next/\:previous tv channel.
tv_step_norm
	Change TV norm.
tv_step_chanlist
	Change channel list.
tv_set_channel channel
	Set the current TV channel.
tv_last_channel
	Set the current TV channel to the last one.
tv_set_freq <frequency in MHz>
	Set the tv tuner frequency.
tv_set_norm <norm>
	Set the tv tuner norm. PAL, SECAM, NTSC and so on..
tv_set_brightness [-100:100]
	Set tv tuner brightness.
tv_set_contrast [-100:100]
	Set tv tuner contrast.
tv_set_hue [-100:100]
	Set tv tuner hue.
tv_set_saturation [-100:100]
	Set tv tuner saturation.
tv_set_brightness [-100:100]
	Set tv tuner brightness.
tv_set_contrast [-100:100]
	Set tv tuner contrast.
tv_set_hue [-100:100]
	Set tv tuner hue.
tv_set_saturation [-100:100]
	Set tv tuner saturation.
gui_[loadsubtitle|about|play|stop]
	GUI actions